Reguladores, Driver para Linternas Led

Regulador de Corriente para Led 3w, 3 Modos,19 Grupos

Driver 7882

0689593933980

Driver Regulador para Led 3w, 1-7v 3A.

3 modos de funcionamiento, 19 grupos

Más detalles

1 a 2 días

1,5916 €

La cantidad mínima en el pedido de compra para el producto es 2

Descuentos, debe estar registrado

Driver Regulador de Corriente 7882

para Led y Linternas Led 3W, 1-7v 3A

3 modos de funcionamiento en 19 grupos

Driver 3w 0.8-7v 7882

Notas:

Two AA is workable with this 3W step-up voltage circuit board.

Select the output selector to 3.5v-3.7v when using two AA setup.

Input voltage: 1-7v <= output selected voltage, maximum input/ouput current at 3A, output voltage selectable from 2V-7V.

MCU light mode selection:

1) Low, Med, High, Strobe, SOS
2) Low, Med, High, Police Strobe, SOS
3) Low, Med, High, Police Strobe, Slow strobe (3HZ), Extreme slow strobe (1HZ), SOS
 
Two seconds light memory. At any low light mode, LED will flash at about 4-5 second interval, switch off the flashlight to switch to the next main-light-modes.

Output options:
1) 1AA Battery: Maximum output (3W) can be obtained by setting the output voltage at 3.5-4V. Maximum current output can reach 700mA with 3A of input from a fully charged NiMH Sanyo 2700mAh AA cell
2) 2 AA
Battery: Output voltage select to 3.5v-3.7v.
3) For Luxenon 5W, set selected output voltage to 6V-7V (no load) using one Li-ion cell.
4) For Luxenon K2, set selected output voltage to 4V-4.5V using one Li-ion cell, output current will be > 2A.

Factory voltage is: 3.5V-3.7V, select output voltage using a small "cross" screw driver by turning the voltage selection screw at the bottom of the circuit board.

How to configure the modes and groups for the 19 mode.

  • Turn on the LED. It will be in some unknown mode and group.

  • Turn the LED off and back on with in 2 seconds which will advance you to the next mode. If it does not change modes, wait just a little longer before turning on the LED.

  • Repeat this, changing modes until you are back to the beginning or can identify what group you are in. If you want to change groups, read the following instructions.

  • Changing mode groups can only be done in "low" mode. When you first enter into low mode, after a couple seconds the light will blink off then on (this will be very apparent). Right then and there, if you turn off the light then back on within the following second or two, you'll enter into the next mode group (still in low mode, but in the next group's low mode.

  • Once you have found the group and mode you want to use, you can turn off the LED. When you turn it on again it will be in the same mode that you left it.

Información técnica extraida del fabricante

Para entrar en modo programación 5 pulsaciones rapidas y dara un destello para indicarte que estas programando el modo uno
si quisieras programar otro modo y no el primero una pulsacion rapida y entonces daria 2 destellos y estarias programando el modo 2 para pasar al 3 lo mismo una pulsacion rapida

Imaginemos que vas a programar el modo uno: 5 pulsaciones rapidas y hace un destello indicandote que estas programando el modo uno despues la linterna enciende desde aprox el 5% de la potencia y va subiendo hasta el maximo y llega al maximo se apaga y vuelve a encenderse duranre 2 segundos al 100% despues empieza con estroboscopio y va subiendo la velocidad y despues hace sos
en el punto que desees que quede fijado el modo 1 (los dos segundos que esta al 100%) apagas la linterna y esperas al menos 10 segundos sin encenderla y el modo uno quedara fijado al 100%.

Con los demas modos igual cuando estes a la potencia o velocidad de strobo deseada para ese modo apagas y esperas 10 segundos.

Damos las Gracias a  forocohes por esta información

 

Comentarios

No hay comentarios en este momento.

Escribe tu opinión, para dejar consultas use También puedes usar nuestro formulario mas completo en https://www.shoptronica.com/home/4860-consulta-de-producto-a-medida.html

Regulador de Corriente para Led 3w, 3 Modos,19 Grupos

Regulador de Corriente para Led 3w, 3 Modos,19 Grupos

Driver Regulador para Led 3w, 1-7v 3A.

3 modos de funcionamiento, 19 grupos

Accesorios

30 productos más en la misma categoría: